Home / Blog / Troubleshooting & Repair

Why Is My Furnace Blowing Cold Air?

By The Sturdi Home Solutions Team2 min read

Quick answer

A furnace usually blows cold air because the thermostat fan is set to ON instead of AUTO, the furnace is still warming up, a dirty filter has caused it to overheat and shut off the burners, or there's an ignition, flame sensor, or drain problem. Check the thermostat and filter first. If the air is still cold, call a technician.

Key takeaways

  • Check the thermostat first: it should be set to HEAT with the fan on AUTO.
  • A clogged filter can make the furnace overheat and shut off its burners while the blower keeps running.
  • High-efficiency furnaces shut down if the condensate drain backs up.
  • If you have a heat pump, warm-but-not-hot air is normal. Cold air is not.
  • If you smell gas, leave the house and call your gas company from outside.

Nothing gets your attention on a cold Chattanooga morning like putting your hand over a vent and feeling cool air. The good news: some of the causes are quick fixes you can check yourself.

Is the thermostat set correctly?

Start here, because it’s the most common cause we see.

  • Mode should be set to HEAT.
  • Fan should be set to AUTO, not ON. When the fan is on ON, it runs all the time, including between heating cycles, and pushes room-temperature air through the vents.
  • Set temperature should be a few degrees above the room temperature.
  • Batteries: if the display is blank or dim, replace them.

Is the furnace still warming up?

When the heat kicks on, the burners light first and the blower waits until the heat exchanger is warm. If your blower starts right away, the first air out of the vents may feel cool for a minute. That’s normal.

When did you last change the filter?

A clogged filter is one of the top reasons a furnace blows cold air. When air can’t flow, the furnace overheats and a safety switch, called the high limit switch, shuts off the burners. The blower often keeps running to cool things down, so you get cool air.

Pull the filter and hold it up to a light. If you can’t see light through it, replace it and give the system a few minutes.

Is the condensate drain clogged?

High-efficiency furnaces (usually with white PVC pipes coming out of them) make water as they run. If the drain line or condensate pump backs up, a float switch shuts the burners down. Look for water around the furnace or a full pump reservoir.

Is it an ignition or flame sensor problem?

If the burners try to light and then shut off after a few seconds, a dirty flame sensor is a likely culprit. It’s a small metal rod that confirms there’s a flame. When it’s coated with residue, the furnace thinks the flame failed and shuts the gas off for safety.

Other possibilities include a failed igniter, a gas valve problem, or a gas supply issue. These need a technician.

Do you have a heat pump?

If your home heats with a heat pump, the air coming out is warm but not hot, often around 90 degrees. That can feel cool against your hand. A heat pump will also blow cooler air briefly while it runs a defrost cycle in cold, damp weather. Cold air that lasts more than 15 minutes is worth a call.

When should you call a technician?

Call us if:

  • The thermostat and filter check out and the air is still cold
  • The burners light and then go out
  • You see error codes on the furnace’s control board light
  • There’s water pooling around the furnace
  • The furnace is short-cycling (turning on and off every few minutes)

If you smell gas, don’t touch switches or try to relight anything. Leave the house and call your gas company’s emergency line from outside.

Our family offers honest furnace repair across Chattanooga. We’ll tell you what’s wrong and the price before we fix it.

Frequently asked questions

Is it normal for a furnace to blow cold air at first?

Yes, for a minute or so. Most furnaces wait for the heat exchanger to warm up before the blower starts, but some air in the ducts will feel cool at first.

Can a dirty filter really stop my furnace from heating?

Yes. A clogged filter restricts airflow, the furnace overheats, and a safety switch shuts off the burners. The blower may keep running and push cool air.

Can I clean the flame sensor myself?

Some homeowners do, but it involves turning off power and gas and removing parts near the burners. If you're not comfortable with that, it's a quick job for a technician.

Why does my heat pump blow cool air in winter?

Heat pump air is often around 90 degrees, which feels cool compared to your body. It may also blow cooler air briefly during a defrost cycle. Air that stays cold for a long time is a problem.

About the author

Sturdi Home Solutions is a family-owned heating and cooling company in Chattanooga, TN. We install, repair, and maintain AC, furnace, and heat pump systems across the Chattanooga area at fair, upfront prices.

Keep reading

All articles →

Ready for honest HVAC service at a fair price?